In an effort to achieve effectiveness and reliability in fiber optics, it is important to pay close attention to certain parameters during connection. A well-crafted and executed placement will mean success while violation of sensitive parameters may mean dire consequences to the connection system. Before embarking on this daunting task, it is relevant to get acquainted with the procedures and consequences inherent in the fibre optic cable installation.
To begin with, ensure to conduct a site survey. A site survey is simply a preliminary visit of the site in order to have insights on the nature of the work to be undertaken. The survey enables you to come up with probable challenges and providing the solutions thereof. During the survey, the site is analyzed for areas demanding special concern while making estimates of the effort and time needed to carry out the duty. This information is particularly important in planning for cable routing.
After surveying, you then develop an effective cable pulling plan. The plan ought to communicate to the fixation team the considerations noted in the site survey. It entails logistics on cable let-off or pulling equipment, splice and intermediate access point locations. In addition, the plan must outline the particular responsibilities of each and every member of the team involved in the fixation.
During this practice, remember to follow the proper procedures. Fibers are sensitive to moisture and thus their ends must be covered using an end cap or heavy tape at all times. When carrying out a pull, never leave the let-off reel unattended as difficult pulls, back-feeding or center-pull techniques may be used.
The effectiveness of the connection largely depends on the length of the bend radius. There is always a minimum value specified for the bend radius; ensure to observe this value. Bending them to smaller radius than this value is inappropriate. The same value applies when coiling or wrapping the cable. There is no significant limit with regards to coiling, but be sure to do it within the constraint of the minimum bend value.
Another important factor to consider is the maximum recommended cable length. Despite the fact that fiber optics are much stronger compared to copper wires, it is imperative not to exceed the maximum tension pulling. The general strength ranking for most outdoor cables is 2700N.
The maximum load value is also a matter worth your concern for long term application. There is a set upper load value for long term performance. Always ensure that the remaining tension after connection is less than the maximum value. For those engaged in vertical clamping, clamp the cables such that the interval between them is regular and sufficient to ensure that the weight remains within the set limit.
Ensure to document each phase of fixation. Documentation of the same provides a record for future reference and maintenance. The task of documentation should be done systematically to enhance flow and order. When in need of whatever type of connection, remember to check out on the above points.
To begin with, ensure to conduct a site survey. A site survey is simply a preliminary visit of the site in order to have insights on the nature of the work to be undertaken. The survey enables you to come up with probable challenges and providing the solutions thereof. During the survey, the site is analyzed for areas demanding special concern while making estimates of the effort and time needed to carry out the duty. This information is particularly important in planning for cable routing.
After surveying, you then develop an effective cable pulling plan. The plan ought to communicate to the fixation team the considerations noted in the site survey. It entails logistics on cable let-off or pulling equipment, splice and intermediate access point locations. In addition, the plan must outline the particular responsibilities of each and every member of the team involved in the fixation.
During this practice, remember to follow the proper procedures. Fibers are sensitive to moisture and thus their ends must be covered using an end cap or heavy tape at all times. When carrying out a pull, never leave the let-off reel unattended as difficult pulls, back-feeding or center-pull techniques may be used.
The effectiveness of the connection largely depends on the length of the bend radius. There is always a minimum value specified for the bend radius; ensure to observe this value. Bending them to smaller radius than this value is inappropriate. The same value applies when coiling or wrapping the cable. There is no significant limit with regards to coiling, but be sure to do it within the constraint of the minimum bend value.
Another important factor to consider is the maximum recommended cable length. Despite the fact that fiber optics are much stronger compared to copper wires, it is imperative not to exceed the maximum tension pulling. The general strength ranking for most outdoor cables is 2700N.
The maximum load value is also a matter worth your concern for long term application. There is a set upper load value for long term performance. Always ensure that the remaining tension after connection is less than the maximum value. For those engaged in vertical clamping, clamp the cables such that the interval between them is regular and sufficient to ensure that the weight remains within the set limit.
Ensure to document each phase of fixation. Documentation of the same provides a record for future reference and maintenance. The task of documentation should be done systematically to enhance flow and order. When in need of whatever type of connection, remember to check out on the above points.
About the Author:
When you are in need of information about reliable fibre optic cable installation, pay a visit to the web pages online here today. You can see details at http://www.datacomsolutions.ca now.
No comments:
Post a Comment