Fibre optic contains a bunch of highly untainted glass used in transmission of data into a beam of light waves. The vulnerability of the cable is high if neither handled with a lot of care nor installed. Therefore proper handling is a necessity during fibre optic cable installation for efficient operation. Ensure you are well advised about the one to have if you are in the city of Vancouver, BC.
The process of installing the wires in different types of environments adhere to certain procedures that one must adopt to ensure not only better handling, efficient operation and placement, but also proper maintenance in future. These guidelines should be carefully followed to the letter. Make sure to get the right advise on which one to have in case you are in the city of Vancouver, BC.
The first thing you need to do is conduct a thorough site survey prior to optic fibre placement. This tries to find out if prevailing conditions on the site require some attention. Probable risks such as high level of temperatures or difficulty in handling machinery should be noted and necessary plans undertaken. Moreover, regulations relating to constructions should be considered. In case of queries regarding the same, they should be addressed by the highest authority.
A comprehensive design before diving in to deployment is then done. This involves establishing criteria for deployment, with regards to the communication paths required, evaluating total hardware requirements, lengths of cable and finally coming up with a breakdown list of hardware components required and specific places they will be used.
Formulate a wire pulling strategy. The system should represent the deliberations taken in during the site survey to the deployment team. For example, the location of transitional access points, the procedures of securing wires and other operating equipment and defined tasks of every individual of the team performing deployment.
Right guidelines should be adhered to. Due to sensitivity of it to moisture, its end needs to be covered always in either end cap or heavy tape. Attending to its indentations must be a norm during a pull since extra or difficult pulls, back feeding or center-pull techniques may be used.
The wires minimum bend radius should not be topped. When doing the placement, it is of essence not to bend to a radius that is beyond its original radius value. Immediately after its installation, and removal of the pulling tension, it cannot be bent to a radius other than the original radius that was defined. The cable is allowed to undergo alterations provided there is no desecration of the lowest bend radius limitations.
Maximum Recommended Load should never be surpassed during any stage of cable deployment. Each wire has a specific strength rating, hence upon placement completion the outstanding tension on the cable should always be less than this value.
Always ensure you place an extra wire at strategic points for better operation. Though, its a good exercise to leave that extra one at either the beginning or end of the wire run.
Finally, doing documentation of your procedural steps in an ordered and simplified manner is encouraged. It helps give assurance of properly deployment and in case of any elevation and future troubleshooting, there will always be a point of reference.
The process of installing the wires in different types of environments adhere to certain procedures that one must adopt to ensure not only better handling, efficient operation and placement, but also proper maintenance in future. These guidelines should be carefully followed to the letter. Make sure to get the right advise on which one to have in case you are in the city of Vancouver, BC.
The first thing you need to do is conduct a thorough site survey prior to optic fibre placement. This tries to find out if prevailing conditions on the site require some attention. Probable risks such as high level of temperatures or difficulty in handling machinery should be noted and necessary plans undertaken. Moreover, regulations relating to constructions should be considered. In case of queries regarding the same, they should be addressed by the highest authority.
A comprehensive design before diving in to deployment is then done. This involves establishing criteria for deployment, with regards to the communication paths required, evaluating total hardware requirements, lengths of cable and finally coming up with a breakdown list of hardware components required and specific places they will be used.
Formulate a wire pulling strategy. The system should represent the deliberations taken in during the site survey to the deployment team. For example, the location of transitional access points, the procedures of securing wires and other operating equipment and defined tasks of every individual of the team performing deployment.
Right guidelines should be adhered to. Due to sensitivity of it to moisture, its end needs to be covered always in either end cap or heavy tape. Attending to its indentations must be a norm during a pull since extra or difficult pulls, back feeding or center-pull techniques may be used.
The wires minimum bend radius should not be topped. When doing the placement, it is of essence not to bend to a radius that is beyond its original radius value. Immediately after its installation, and removal of the pulling tension, it cannot be bent to a radius other than the original radius that was defined. The cable is allowed to undergo alterations provided there is no desecration of the lowest bend radius limitations.
Maximum Recommended Load should never be surpassed during any stage of cable deployment. Each wire has a specific strength rating, hence upon placement completion the outstanding tension on the cable should always be less than this value.
Always ensure you place an extra wire at strategic points for better operation. Though, its a good exercise to leave that extra one at either the beginning or end of the wire run.
Finally, doing documentation of your procedural steps in an ordered and simplified manner is encouraged. It helps give assurance of properly deployment and in case of any elevation and future troubleshooting, there will always be a point of reference.
No comments:
Post a Comment